The Best of All quilt block is a lovely traditional quilt block that finishes at 12″ square. But I’m going to show you a non-traditional way of constructing this block. Let’s get started!
Fabric Requirements for Best of All Block:
Light/White: 24 – 2.5″ squares, and 4 – 3″ squares
Medium/Blue: 4 – 3″ squares, and 8 – 2.5″ squares
Dark/Green: 8 – 2.5″ x 4.5″ rectangles
Dark/Black: 1 – 4.5″ square
Flying Geese Units:
First thing you need to do is make 8 Flying Geese units using the Dark/Green 2.5″ x 4.5″ rectangles and 16 Light/White 2.5″ squares. You can find my tutorial on Flying Geese units at: https://fabric406.com/how-to-sew-a-basic-flying-geese-block/. Of course, this is the one picture I forgot to take so I had to crop a different picture to show the Flying Geese unit. Set four of these units aside to use later in the block.
Double Geese Units:
This is where the non-traditional way to piece this block together starts. Basically, we are going to go through the same steps used to make a Flying Geese unit but we’ll be using one of the Flying Geese units and 2 Medium/Blue 2.5″ squares. I’m going to call this unit a Double Geese unit.
First you will need to mark a diagonal line on the back of the two Medium/Blue 2.5″ squares.
Place one square on one end of Flying Geese unit, right sides together as shown by the top unit in the picture below. Sew close to the marked line in what will be the seam allowance.
Match the corners of the square and press (middle unit in photo).
Open up the square and trim the seam allowance as shown in the bottom unit in the picture.
So I tried a different layout taking pictures – this one didn’t turn out so good!
Place the other Medium/Blue 2.5″ square on the opposite end of the Flying Geese unit and repeat the process to complete the Double Geese unit.
Repeat to make a total of four Double Geese units.
Pair up one of the set aside Flying Geese units with one Double Geese unit and sew together as shown below. Press the seam allowance toward the Flying Geese unit. Honestly, this was the hardest step for me to get the seams to match. I used pins at start and end, went slow, and sewed with the Double Geese unit on top. The fourth one looked better than the first!
Now for the corner units! Make 8 Half-Square Triangle (HST) units using the 4 Light/White 3″ squares and the Medium/Blue 3″ squares. Trim /square up the HST to a 2.5″ square. You will find my directions for making HSTs at https://fabric406.com/how-to-sew-a-basic-half-square-triangle-block/
Lay out 2 of the HSTs and 2 Light/White 2.5″ squares as shown below.
Sew into two rows and press the seam allowances toward the Light/White 2.5″ squares as shown in the picture below.
Sew the two rows together and press the seam allowance as shown below. I do not recommend pressing using the tweek/twirl/furl method in this unit.
Putting it all Together:
Lay out all of the units you have sewn plus the center Dark/Black 4.5″ square as indicated in the photo below. You may need to turn the Corner units 180 degrees so that you can get the seam allowances to nest.
Sew the units into three rows and …
Press the seam allowances away from the Flying Geese/Double Geese units as shown.
Piece the rows together and …
Press the seam allowances toward the center of the block as shown below. Voila! You’re done!
This block is a little challenging but the way I’ve described making the Double Geese units is much faster than the traditional way. The unit also laid nicer. Traditionally, you would cut triangles and sew them to a small center square – sewing with bias edges can be tricky.
I love the look of this block and don’t be shy about using darker colors in it – it will look great! I hope you love it too.