How to Sew a Ranger's Pride Quilt Block

Posted by Elaine Huff on

Today we're going to learn how to sew a Ranger's Pride quilt block! This block is not hard to put together with a simple Pinwheel block in the center and a border that's applied using partial seam construction. There's an added bonus when you put the blocks together too (more on that later). Let's get started!

Fabric Requirements for a 12" Finished Ranger's Pride Quilt Block:

  • Light/Ivory: 2 - 5" squares, 8 - 2.5" squares, and 4 - 2.5" x 6.5" rectangles
  • Dark 1/Brown: 4 - 2.5" x 4.5" rectangles
  • Dark 2/Red: 2 - 5" squares

rangers pride fabric requirements

Sewing Directions:

Half-Square Triangle Units:

Step 1:

Using the Light/Ivory 5" squares and the Dark 2/Red 5" squares sew together four Half-Square Triangle units. You can find my tutorial on making Half-Square Triangles at https://fabric406.com/blogs/fabric406-blog/how-to-sew-a-basic-half-square-triangle-block Trim/square up the units to 4.5" square.

rangers pride hst

Center Pinwheel Unit:

Step 2:

Using the Step 1 Half-Square Triangle units, sew a pinwheel as shown below. You can find my tutorial for sewing a Pinwheel block together at: https://fabric406.com/blogs/fabric406-blog/pinwheel-quilt-block-pattern

pinwheel unit

Flying Geese Units:

Step 3:

Using the Dark 1/Brown 2.5" x 4.5" rectangles and the Light/Ivory 2.5" squares piece together four Flying Geese units. My tutorial for sewing Flying Geese blocks is here: https://fabric406.com/blogs/fabric406-blog/how-to-sew-a-basic-flying-geese-block

rangers pride flying geese

Border Units:

Step 4:

Sew together a Step 3 Flying Geese unit and a Light/Ivory 2.5" x 6.5" rectangle as shown in the picture below. Press the seam allowance toward the Light/Ivory rectangle. Repeat for a total of four Border units.

rangers pride border unit

Putting It All Together:

Step 5:

Lay out the Center Pinwheel unit and the Border units as shown in the picture below. Make sure you get the Border units' orientation correct!

rangers pride 5

Step 6:

Now we get to start on the partial seam construction to put this block together. It's not hard to do at all. Sew the top Border unit to the Center Pinwheel unit, leaving a couple of inches free at the end that has the Flying Geese unit. You can see what I'm talking about in this picture and the next picture.

rangers pride 6

Step 7:

Press the seam allowance away from the center of the block as shown in the picture below.

rangers pride 7

Step 8:

Now you can sew the right Border unit to the Step 7 unit as shown below. Your seams should nest nicely so you get good points where the Pinwheel unit and the Flying Geese unit meet.

rangers pride 8

Step 9:

Press the seam allowance away from the center of the block as shown in the picture below.

rangers pride 9

Step 10:

Continuing in a clockwise fashion, sew the Border units to the Center Pinwheel unit and press the seam allowances away from the center of the block as shown in the pictures below.

rangers pride 10-1

rangers pride 10-2

Step 11:

Finish sewing the Ranger's Pride block together by closing up that partial seam that you started with. See, that's not so hard.

rangers pride

Step 12:

Finish pressing that last seam allowance and you are done!

rangers pride 12

Yardage:

To made four blocks, you will need one 5" x width of fabric (WOF) strip of both the Dark 2/Red and the Dark 1/Brown fabric, and one 10" x WOF strip of the Light/Ivory fabric. 

In Conclusion:

I found the Ranger's Pride quilt block was fun to put together mainly because I was excited about the secondary Pinwheel that would appear when blocks were sewn together. Below I have a computer rendition of what a 4 x 4 quilt would look like.

rangers pride quilt

I also think this would be an amazing scrappy quilt. I would use one background fabric and then just dig into my scrap pile (piles actually!!). The quilt has lots of movement with the two types of pinwheels.

I hope you have enjoyed this Ranger's Pride quilt block.

Happy Quilting!

Elaine


Share this post



← Older Post Newer Post →


  • a nice change & addition to the pinwheel block; yes, scrappy would be quite nice.

    Sue Mac Donald on

Leave a comment

Please note, comments must be approved before they are published.